Z-World XP8900 Uživatelský manuál Strana 64
- Strana / 114
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
PK2100
B-4 s Appendix B: Specifications
Jumper and Header Specifications
Figure B-3 shows the locations of the PK2100 headers and jumpers.
H11
J3
J9
1
1
J1
114
1
2
J8
H7
H9
H1
J7
1
1
1
1
H5
H6
H4
J4
1
1
2
H8
J11
Figure B-3. Locations of PK2100 Headers and Jumpers
The jumper configurations are described in Table B-2, Table B-3, and
Table B-4..
Table B-2. PK2100 Header Descriptions
Header Description
H1
When H1 is connected, a 10 kΩ excitation resistor, RP6A, is
connected between the +10 V reference and the high-gain
input AD+.
H7
Connect a jumper across H7 to cause differential inputs AD+
and AD– to be balanced in gain. If the jumper is discon-
nected, the gain is greater on the AD+ side, so that if both
inputs are set to 5 V, the output of the operational amplifier is
5 V. Use this feature to accept input from bridges where the
taps are nominally at +5 V.
H9
A jumper across H9 connects the internal battery to relay 1
N.O. contact. Use H9 when a battery self-test circuit is to be
implemented by connecting a switched load to the battery.
H11 A jumper is normally installed across H11 to connect K to the
+24 V power supply. Disconnect only if a separate power
supply is to be used for high-current outputs O1–O7. In that
case,
K must be connected to that power supply.
J7 Connect 2-3 on J7 for voltage output on the DAC channel
(factory setting). Connect 1-2 for 20 mA current output.
- Users Manual 1
- CONTENTS 3
- Software Reference 5-1 4
- Contents s v 5
- ABOUT THIS MANUAL 7
- Terms and Abbreviations 8
- Table 3. Icons 9
- PK2100x s About This Manual 10
- PK2100 OVERVIEW 11
- PK2100 Overview 12
- PK2100 Features 13
- PK2110 Features 13
- PK2120 Features 13
- PK2130 Features 13
- Options and Upgrades 13
- 1-4 s PK2100 Overview 14
- GETTING STARTED 15
- Initial PK2100 Setup 16
- Establishing Communication 17
- Running a Sample Program 17
- 2-4 s Getting Started 18
- I/O CONFIGURATIONS 19
- PK2100 Inputs and Outputs 20
- I/O Configurations s 3-3 21
- Universal Inputs 22
- Temperature Sensor 23
- +10-V reference 23
- Digital Inputs 24
- Counter 1 25
- Counter 2 25
- Jumper H7 installed 27
- Relay Outputs 29
- Digital Outputs 30
- Inductive 31
- D.C. in D.C. in 31
- Digital output 31
- 3-14 s I/O Configurations 32
- SYSTEM DEVELOPMENT 33
- Programming 34
- Virtual Driver 35
- Virtual Driver Services 36
- System Development s 4-5 37
- Virtual Driver Variables 38
- System Development s 4-7 39
- Downloading Code 40
- Attainable Baud Rates 41
- Z180 Serial Ports 41
- 4-10 s System Development 42
- SOFTWARE REFERENCE 43
- Driver Software 44
- Analog Input 45
- 5-4 s Software Reference 46
- Analog Output 47
- High-Speed DMA Counter 48
- Battery-Backed Clock 49
- 5-8 s Software Reference 50
- Software Reference s 5-9 51
- EEPROM Read / Write 52
- Flash EPROM Write 52
- Communication 53
- subdirectory 54
- Program Description 55
- TROUBLESHOOTING 57
- Out of the Box 58
- Dynamic C Will Not Start 59
- Dynamic C Loses Serial Link 59
- PK2100 Resets Repeatedly 59
- Common Programming Errors 60
- APPENDIX B: SPECIFICATIONS 61
- Hardware Dimensions 62
- Table B-4 64
- Header Pins Description 65
- Connectors 67
- POWER MANAGEMENT 69
- Power Failure Interrupts 70
- Heat Sinking 71
- C-4 s Power Management 72
- I/O MAP AND 73
- INTERRUPT VECTORS 73
- Address Name Description 74
- Table D-2. Write Registers 76
- Table D-3. Read Registers 78
- Address Bits Symbol Function 78
- Interrupt Priorities 80
- APPENDIX E: EEPROM 81
- Address Definition 82
- Field Calibration 84
- APPENDIX F: PLCBUS 85
- PLCBus Overview 86
- PLCBus Header 87
- Table F-2. PLCBus Registers 88
- Appendix F: PLCBus s F-5 89
- A1 A2 A3 Meaning 90
- Expansion Bus Software 91
- F-8 s Appendix F: PLCBus 92
- Appendix F: PLCBus s F-9 93
- F-10 s Appendix F: PLCBus 94
- Appendix F: PLCBus s F-11 95
- F-12 s Appendix F: PLCBus 96
- BATTERY 97
- G-2 s Appendix G: Battery 98
- Battery Cautions 99
- G-4 s Appendix G: Battery 100
- BOARD LAYOUT 101
- Index s I-1 103
- PK2100I-2 s Index 104
- Index s I-3 105
- PK2100I-4 s Index 106
- Index s I-5 107
- PK2100I-6 s Index 108
- Index s I-7 109
- PK2100I-8 s Index 110
- Index s I-9 111
- PK2100I-10 s Index 112
- Printed in U.S.A 113
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce